Plumbers NZ is New Zealand's largest online plumbing, gas and drainage resource. Plumbing exam help, plumbing news, directory and free quotes.

Author Topic: Am I reading this right?  (Read 3528 times)

0 Members and 1 Guest are viewing this topic.

Offline Badger

  • Hero Member
  • *****
  • Posts: 1980
  • Karma: +222/-151
Am I reading this right?
« on: March 02, 2013, 10:08:40 AM »
Am I reading this right?..... see attachment taken from Febuary 2013 UpSkill ATT Mag.



Linkback: https://www.plumbers.nz/codes-standards-health-and-safety/10/am-i-reading-this-right/1385/
You can't choose who you are.....but you are the sum of your choices.......

Offline Badger

  • Hero Member
  • *****
  • Posts: 1980
  • Karma: +222/-151
Re: Am I reading this right?
« Reply #1 on: March 02, 2013, 10:14:41 AM »
"If you are replacing all or even a small part of metal pipework or any metal fittings with a plastic product (non-metalic), you must not begin work until a registered electrician has determined the earthing requirements for the system"

 

Offline Badger

  • Hero Member
  • *****
  • Posts: 1980
  • Karma: +222/-151
Re: Am I reading this right?
« Reply #2 on: March 02, 2013, 10:32:09 AM »
If you look closely at the bottom left picture, it looks like the pipe on the top end of the copper pipe that is being bridged out carries on in Bute from the wingback screwed into timber frame.

Offline Badger

  • Hero Member
  • *****
  • Posts: 1980
  • Karma: +222/-151
Re: Am I reading this right?
« Reply #3 on: March 02, 2013, 12:36:50 PM »
May be power travelling in the water?

But I didn't realise I had to get a sparky before I start any pipe work?

Offline robbo

  • Hero Member
  • *****
  • Posts: 1259
  • Karma: +83/-7
Re: Am I reading this right?
« Reply #4 on: March 02, 2013, 04:57:20 PM »
hi guys, yes Badger i have had sparks jumping the gap when cutting an inlet pipe to a prv,(wasn`t useing a jump lead) called the power supplier who checked it out and came up with the answer of power leaking from a house three houses away was causing the problem, anyway continued on after useing jump lead, cheers
P.S. is it red lead for hot water pipe and black lead for cold, lol.

Offline Badger

  • Hero Member
  • *****
  • Posts: 1980
  • Karma: +222/-151
Re: Am I reading this right?
« Reply #5 on: March 02, 2013, 07:05:28 PM »
I know about the cross bonding with a lead mate,they drummed it in to us in the gas board(spark and gas isn't the best).... what I am wondering is do you have to get a sparky in to replace a pipe?

Offline gordyplum

  • Jr. Member
  • **
  • Posts: 63
  • Karma: +7/-0
Re: Am I reading this right?
« Reply #6 on: March 03, 2013, 10:00:26 PM »
Cant remember the last time i cut copper pipe with an hacksaw!!

Offline hefzibah

  • Jr. Member
  • **
  • Posts: 19
  • Karma: +1/-0
Re: Am I reading this right?
« Reply #7 on: August 08, 2013, 09:04:45 PM »
can't remember the last time i saw PRV that old.

Offline Enn

  • Full Member
  • ***
  • Posts: 192
  • Karma: +22/-1
  • Ex-chef
Re: Am I reading this right?
« Reply #8 on: August 08, 2013, 10:43:34 PM »
Hey that prv's not that  old, i see quite a few of them, its the copper ones that are old.... ill see if i can post a pic of of one next time I'm cleaning the shed. or the plastic u.f.o's

As for getting a sparky in to check the earthing, a electrical inspector told me if there is no earth stake then the earthing will be via the galv piping water utility, and a good idea to have the earthing checked.
Getting some one to pay is the usual problem. More cost for the client and quite frankly most don't give a rats arse about it. all they want is the cheapest they can get.

Even more scope for the ignorant DIY or cowboy its not the first time Ive replaced a hwc that has been home wired with a bit of old vacuum cleaner flex and chocolate block connectors, quite a bit of load for that wire.....
''Never have so many been fooled by so few''
Plumbing is not a career it is a disease....


Share via digg Share via facebook Share via linkedin Share via twitter

Similar Topics

  Subject / Started by Replies / Views Last post
xx
Second Reading of the Plumbers, Gasfitters, and Drainlayers Amendment Bill 2006

Started by Jaxcat

27 Replies
7146 Views
Last post April 18, 2013, 06:56:22 PM
by Rodza1
 
Share this topic...
In a forum
(BBCode)
In a site/blog
(HTML)